3-Axis Vibration Test Systems/Electrodynamic Vibration Shaker Test Machine

Product Description

3-Axis Vibration Test Systems
 

 

Product Description

ISTA 6A AMAZON Random Vibration Testing Equipment is widely used in defense, aviation, aerospace, communications, electronics, automobiles, home appliances, and other industries. This type of equipment is used for discovering the early faults, simulating the actual working condition and the structure strength test, the product application is wide, the application width is obvious, the test effect is remarkable and reliable. Sine wave, FM, sweep, programmable, frequency multiplier, logarithm, maximum acceleration, amplitude modulation, time control, full function computer control, simple fixed acceleration/fixed amplitude. Equipment through continuous failure to run 3 months of testing, stable performance, reliable quality.


Charateristics:
1.Ultra mute work
2.The machine base uses the high quality material, installs conveniently, the operation is smooth, does not need to install the The, the control circuit digitization control and the display frequency, the PID adjusts the function, causes the equipment work to be more stable, reliable, sweeps the frequency and the fixed frequency operation way, adapts to the different profession test request To solve the interference of the strong electromagnetic field to the control circuit.
3.Increase the working time set, so that the test product reaches the accurate test time.

How to use:
1, the control manual to complete the procedure
2, such as Operation error so that can not work, you can use the recovery method of the steps of the input, and then set a single group or other running steps.
3, before use to press the external start switch, appears COO namely lets go, opens the key.
4, Machine Body:
1) The table body foot sleeve as far as possible fixed
2) power supply on/work in the output line can not be unplugged
3) Place the level as far as possible
4) components can be changed, the line should not be changed or from the connection.
5) The Taiwan body must not be all or part of the reorganization, only according to specifications for a single component and with the original confirmation password.
5, the amplitude inside the code
1) Do not adjust too large before or after the boot
2) low-key amplitude of high amplitude modulation
3) Control Panel Amplitude Knob placed in the middle position test items: placed to focus on the main point, reduce the left flat right.
4) control Box: Can not be placed on the top or underground operation
6, Inside Code:
1) reset when running or operating incorrectly
2) Control The Reset method step, each inside code only set one time to save can
3 usually must use the internal code can not be set randomly
7, Control Box:
1) The connecting line of the body must be locked tightly after hanging
2) the vibration direction switch and the output connection line are correspondence, can not connect the wrong
8, testing: Non-special test should use full wave test
9, the machine body can not produce the collision sound, the upper and lower center axis mutual touch will cause the spring steel piece rupture to be immediately shut down, amplitude modulation is adjusted small then turns on.
10, Attention:
1) The use of computer models can not be used for shaking table control
2) can not reload the driver;
3) for the Ista-ia test, the operator to protect the sample, to prevent the test pieces slide out of the table;
4) gear gearbox replacement regularly;
5) Cut off all power when not working, keep clean; 5, non-staff can not operate at will;
6)Do not arbitrarily change internal components and lines




Parameter:

Shaker
Sine force (peak)	30kN
Shock force (peak)	60 kN
Frequency range	5~2,600 Hz
Displacement (continuous)	100 mm
Max. Velocity	1.8 m/s
Max. Acceleration	75 G
Armature Diameter	445 mm
1^storder resonant frequency	2,400 Hz
Allowable eccentric moment	>500 Nxm
Armature weight	40 kg
HE/ST screw dimension	M10 (metric)
Axial vibration isolation frequency	<3 Hz
Max. Payload	500 kg
Magnetic flux leakage	≤1 mT
Dimensions (L×W×H, unpacked)	1,330x860x1,250 mm
Weight (unpacked)	2,500 kg
Installation	Rubber mat (anchor bolts required)
Power Amplifier
Amplifier output	30 kVA
SNR	>65 dB
Rated output voltage	120 Vrms
Amplifier efficiency	> 90%
Dimensions (L×W×H, unpacked)	800x900x2,100 mm
Weight (unpacked)	500 kg
Blower
Air volume	0.46 m^3/s
Power	7.5 kW
Air duct diameter	200 mm
Air pressure	8.8kPa
Installation	Able to connect to ceiling (up to two 90 degree bends), max 20' run
Horizontal Slip Table
Dimensions	600x600 mm
Thickness	45 mm
Frequency limit	2,000 Hz
Effective mass	54 kg
Note: 1. High pressure oil-film bearing is used for better uniformity.
Vibration Controller and Accelerometer
Vibration Controller VT-9008-4		4 Channel Vibration Controller with Sine and Self Calibration.
Accelerometer   EA-YD-181	100mV/g, Range: 50g, Working Freq.: 1-10kHz, Weight: 11gram, with 10ft low noise cable
Other supported functions/accessories
Environmental chambers	Supported
Mobile devices	Customizable
Insulation boards	Customizable
Fixture	Customizable
Working environment of the system
Temperature range	0-40ºC
Humidity range	0~90% , no condensation
Power requirements	380V/3ph/50Hz, 40kVA
Compressed air pressure	0.6 Mpa

Our Advantages

Our Company Introduction:
HAIDA INTERNATIONAL is a professional manufacturer of various kinds of testing equipments over 24 years. HAIDA products are widely used in paper products, packaging, ink printing, adhesive tapes, bags, footwear, leather products, environment, toys, baby products, hardware, electronic products, plastic products, rubber products and other industries, and applicable to all scientific research units, quality inspection institutions and academic fields.

After Sales Service

After-Service:
Should any issues arise during your testing process, we guarantee:
Timely Response: A formal reply within 48 hours.
Swift Resolution: A proposed solution within 3 working days.
Comprehensive Support: Access to English operation manuals, instructional videos, and video conference assistance.


Why Choose Us? 
Global-Ready Design
Built-in voltage auto-switching (110V/220V), international plug compatibility, and safety-certified indicator protection.
Exceptional After-Sales Support
18-month comprehensive warranty. Industry-unique benefit: Complimentary repair service for controllers - even competitor units. Simply ship the controller to us.
Binding Quality Commitment
A formal Quality Assurance Letter accompanies every contract signing, guaranteeing performance and building trust.
Industrial-Grade Protective Packaging
(e.g., Triceratops) is individually wrapped in anti-static bubble film and secured in reinforced wooden crates. This ensures:
• Shock absorption & impact resistance
• Moisture & corrosion protection
• Non-toxic, odorless materials
• Optimal transparency for inspection
FAQ:Q: Are you a trading company or manufacturer?
A: Integrated manufacturer with 21+ years specializing in test equipment and 6 years of export expertise.
Q: What is your delivery timeline after order confirmation?
A:Standard orders: 10-25 working days
Stock orders: Ship within 3 days
Note: Lead times vary by product specifications and order volume.
Q: What are your warranty and after-sales service terms?
A:12-month comprehensive warranty on all testing machines
Industry-unique benefit: Complimentary controller repairs (including non-HAIDA units)
Post-warranty support: Dedicated technical team for troubleshooting, operational guidance, and complaint resolution
Q: How do you ensure product quality and service?
A:100% pre-shipment inspection with full performance testing
Global-ready design: Voltage auto-switching (110V/220V), international plugs, safety-certified indicators
Multi-tier training support:
✓ Instructional operation videos
✓ On-site engineer training (upon request)
Market-proven reliability: 
Globally recognized by industrial users
Q: Do you offer product customization?
A: Yes, we develop tailored solutions based on your technical parameters and application requirements.