Programmable Environmental Testing Machine Salt Spray Corrosion Testing Chamber/Instrument
Description:
Salt Spray Tester adapted to the surface treatment of various materials, including paint, electroplating, organic and inorganic coating, anode processing, antirust oil and so on, after these anti-corrosive treatment to test the corrosion resistance of their products.
Operation and Control:
A digital temperature controller enables the operator to independently set the chamber temperature and the temperature of the bubble tower. The chamber isHeated by a wrap-around heater jacket which is bonded to the exterior surface of the internal workspace to protect it from damage from the corrosive climate reated inside the test chamber. The bubble tower humidifies the compressed air on the way to the salt fog atomizer and is heated by an immersion heater. Both the cabinet and bubble tower are equipped with over-temperature protection safety thermostats.
The water level in the bubble tower can be filled with de ionized water in one of two ways - either automatically, if the chamber is connected to a pressurized water supply, or by hand, using the manual filler port.
A separate external salt solution reservoir, where the salt later to be atomized into a fog is mixed and held. The utilization of a separate external salt solution reservoir facilitates quick change-overs when going from an ASTM standard to a DIN standard Salt fog fall-out is controlled by an adjustable flow control meter located on the control panel. This, coupled with the integrated air pressure regulator and gauge, is used to ensure a uniform and continuous fall-out of salt fog onto the samples under test.
Standard Parameters
| Model |
HD-E808-90 |
| Inner Box Size (L× W× H) |
90× 60× 50 cm |
| Outside Box Size(L× W× H) |
141× 88× 128 cm |
| Equipment Material |
Both inside & outside shell of salt spray chamber adopt imported P. V. C rigid plastic board, and tank cover uses imported transparent P. V. C. rigid plastic board |
| Temperature Range |
35 centigrade degrees to 55 centigrade degrees |
| Temperature Fluctuations |
≤ ± 0.5 centigrade degrees |
| Temperature Uniformity |
≤ ± 2 centigrade degrees |
| Temperature Precision |
± 1 centigrade degrees |
| Test Chamber Temperature |
Salt Spray Method (NSS ACSS)35± 1 centigrade degrees
Corrosion-resistant Testing Method (CASS) 50± 1 centigrade degrees |
| Saturated air Barrel Temperature |
Salt Spray Method (NSS ACSS)47± 1 centigrade degrees
Corrosion-resistant Testing Method (CASS) 63± 1 centigrade degrees |
| Brine Temperature |
35 centigrade degrees± 1 centigrade degrees |
| Spray Quantity |
1.0~2.0 ml / 80cm2 / hr |
| PH |
Salt Spray Method (NSS ACSS6.5~7.2)
Corrosion-resistant Testing Method(CASS)3.0~3.2 |
| Lab Volume |
270L |
| Brine Tank Capacity |
25L |
| Power |
AC220V, 10A |
| Multiple Safety Protection Devices |
Current discharge protection, over pressure protection, over temperature protection, over load fuse protection |
| Accessories |
Testing Salt/ Measuring tank/ Equipment each 1 set |
| Standard |
CNS: 3627, 3385, 4159, 7669, 8886;
JIS: D0201, H8502, H8610, K5400, Z2371;
ISO: 3768, 3769, 3770;
ASTM: B117, B268 |
Product Features
1, Durable hard 8 mm PVC construction, anti-corrosion and easy to clean.
2, Reservoirs with mixing system on stand.
3, Separate heating system apart from salt testing chamber to ensure accurate result and protect circuit.
4, Exposure zone lined with corrosion-resistant PVC sheets.
5, Clear cover allows viewing of test conditions.
6, Peaked cover prevents dripping of condensation onto samples.
7, Water seal and water level protection system.
8, Heated humidifying tower with air relief valve, adjustable tower tip to orient salt fog.
9, Automatic DI water fills to humidifying tower.
10, Digital temperature control.
11, Integral over-protection on heaters.
12, Low water cut-off protection on humidifying tower.
About HAIDA
Haida products are widely used in paper products, packaging, ink printing, adhesive tapes, bags, footwear, leather products, environment, toys, baby products, hardware, electronic products, plastic products, rubber products and other industries, and are applicable to all scientific research units, quality inspection institutions and academic fields. Our products meet UL, ASTM, JIS, GB,SO, TAPPI, EN, DIN, BS and other domestic and international standards.
Packaging & Shipping:
Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.
After-service:
If you face any problems in future during testing process we promise we will give you a reply within 48 hours and solution provide within 3 working days. We can offer operation video and English operation muanual. We can provide video-con.
Audited Supplier 
){kind=link}