This product is no longer promoted on Made-in-China.com. If you find any infringement or sensitive information of it, please contact us for handling. Thank you.
  • Paper Package Clamp Compression Testing Equipment
  • Paper Package Clamp Compression Testing Equipment
  • Paper Package Clamp Compression Testing Equipment

Paper Package Clamp Compression Testing Equipment

Contact Supplier

Diamond Member Since 2011

Suppliers with verified business licenses

Manufacturer/Factory

Basic Info.

Model NO.
HD-A534
Control
Computer Control
Weight
500-1000Kg
Power Source
AC380V
Warranty
One Year
Device Width
Less Than 2.5m
Delivery Time
15 Days After Receive The Deposit
Clamping Plate Adjustable Height
0~1000mm
Motor
Motor
Maximum Specimen Weight
600kg
Clamping Plate Size
Height 48inch*Depth 48inch
Clamping Plate Adjustable Width
200~2000mm
Base Plate Dimension
2200*2100mm
Transport Package
Strong Wooden Case
Specification
ASTM D642 \ ISTA 6- SAMS CLUB
Trademark
Haida
Origin
China
HS Code
9024800000
Production Capacity
150 Sets Per Month

Product Description


                       Paper Package Clamp Compression Testing Equipment


Introduction:
 
The ISTA Package Clamping Force Testing Machine is simulated the impact strength of packaging in the real circumstance of transportation, for example, the transportation of goods. This product is applied to the scientific research institutions, colleges, packaging technique test centers, packaging material manufacturers and foreign trade or transportation departments.
 
 Paper Package Clamp Compression Testing Equipment

Design Standard:
 

ASTM D642\ ISTA 6- SAMS CLUB\ ISTA 3J
 
 

Technical Parameters of ISTA Package Clamping Force Testing Machine: 
(The table parameters for the company Standard Model parameters, we support customer customization parameters)
Specimen shapeParallelepiped transport package
Max. Specimen weight500kg
Clamping pressure forceAccording to the transport diagram on the test sample, the operator can add 400~3000Lb (adjustable) pressure force on the corresponding surface
Clamping board sizeH*D 48*48inch
Clamping board adjustable height0~500mm
Elevation speed10~300mm/min optional
Clamping board expansion width200~2000mm
Baseboard dimensionW*D 1500*1500mm
Clamping board requirementMake sure the two clamping board are flat, parallel and non-deform under the work condition(2000Pound) and clamp board and land are vertical. Clamping board thickness no less than 25mm.
Corrector of forceForce value display used to correct clamping force
Force precisionNational standard 1.6 level
OperationManual operating rod simulates fork truck actual operating actions such as clamping control, opening, lifting up, lifting down or automatic switching mode operation (clamping board thickness no less than 25mm)
Device widthLess than 2.5m

Clamp Compression Testing Method of Large Products :

1.Before placing the packaged product between platens, verify that the clamp force using the clamp indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
 
2.Each time the product is clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

3. Apply the clamp force on the sample with the platens resting on the floor and the front edge of the platens flush with the front of the package. If the package is too large for the clamps to be flush to front edge (i.e., large refrigerator, tractor etc.), clamp as close to the edge as possible.

4. Clamp the product a total of 10 times in the flush orientation.

5. Apply the clamp force on the packaged product with the platens in a 6×6 inch(15.2x15.2cm) offset position(see fig 5 ). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamp to be positioned 6-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

    1)Exception number 1: for large products with an obvious, visible external skid(see fig 6), offset clamp testing is not conducted if the product does not extend beyond any part of the skid and there is some form of handling graphic or note that indicates to clamp only from the skid. If there is no graphic or not indicating this or there is some overhang beyond the skid, then the entire clamp test protocol is conducted.

    2) Exception number 2: If the product height, when placed in its normal shipping orientation, is ≤ 12 inches, the 6 x6 inch offset testing is not conducted.

6. Clamp the product a total of 10 times with the clamp in the 6 x6 inch offset position.

7. Repeat step 5.2.5 except with a 2 x6 inch offset clamp position. The 2 x6 inch offset is similar to the 6 x6 inch offset except the platens are oriented such that they are 2-inches from the floor and 6-inches back from the package's front edge. If the package is too large for the clamps to be positioned 2-inches from the front edge (i.e., large refrigerator, tractor etc.), clamp as close to this position as possible.

8. Repeat flush and offset clamping on all other sides of the product that are indicated in the handling graphics as acceptable for clamp handling.
According to verdict standards, if there is one item failed the test, then put forward the "Test Failure Handling Sheet".


Clamp Compression Testing Method of Small Products :

Before clamp testing, verify that the clamp for using the clamp force indicator. The indicator should be placed between the axes of the platen articulation points approximately 1/2 way up the platens.
During clamp compression testing of small products, 4 samples will be utilized as outlined below.

1. If, when oriented for clamp testing (based on the handling graphics) the sides perpendicular to the platens of a single sample ≤ 24" (61cm), then the 4 sample should be placed in a"side by side"oritentation as shown to the fig 1(with 2 samples on the bottom and 2 on the top)

2. If, when oriented for clamp testing the sides perpendicular to the platens of a single sample are >24" (61cm),, then the 4 samples should be placed in a top-bottom orientation as shown fig 2. If, when placed 4-high, any of the samples are completely above the top of the platens, that sample can be removed from clamping in this orientation only(fig 3 shows 3 MHC's ready for clamp testing with the 4th sample removed from testing in this orientation)

3. Each time the samples are clamped, the force should be applied for a minimum of 15 seconds and not to exceed 1 minute.

4. Apply the clamp force on the samples with the platens resting on the floor and the samples flush with the front edge of the platens (see fig2). If the samples are too large for the clamps to be flush to front edge, clamp as close to the edge as possible.

5. Clamp the product a total of 10times with the clamps in the flush orientation.

6. Apply the clamp force on the packaged product with the platens in a 2×2 inch offset position(see fig 3). Both the horizontal and vertical offset dimensions are measured at the front bottom corner of the platen. If the package is too large for the clamps to be positioned 2-inches from the front edge, clamp as close to this position as possible.

7. Clamp the product a total of 10 times with the clamps in the offset position.

8. Repeat the flush and 2x2 inch offset camping on all other sides of the product that are identified in the handling graphics as acceptable for clamp handling. Please note, depending on the box geometry, you may use both the side-by-side and top-bottom orientation during clamp testing.


The introduction of Haida
Haida products are widely used in paper products, packaging, ink printing, adhesive tapes, bags, footwear, leather products, environment, toys, baby products, hardware, electronic products, plastic products, rubber products and other industries, and are applicable to all scientific research units, quality inspection institutions and academic fields. Our products meet UL, ASTM, JIS, GB,SO, TAPPI, EN, DIN, BS and other domestic and international standards.
 
If you face any problems in future during testing process we promise we will give you a reply within 48 hours and solution provide within 3 working days. We can offer operation video and English operation muanual. We can provide video-conference. If customers require on-site service, the transport and travel expense shall be borne by customer.
1. Pre-service
    24 Hours online service for your consult.
    Help choose right model,and a series  of service,person,advise. main web site:http://haidaequipment.en.made-in-china.com   
2. Middle service
    --Give you best offer
    --Provide discount for many sets order
    --Do customer's request:
    --Choose payment term you convienent.
    --Promptly production and delivery,inform you in time.
    --Can provide invoice value as you like to decrease your tax.   
3. After sale service
   --1 year warranty service and all life maintenance.
   --Technical Egineer are avalible for oversea trainning.
   --Free change for some parts
   --Remote control technical consult
   --Free installation DVD
   --Maintenance plan
4,Commitment:
We will sign a letter of commitment while we sign the contract, which will improve your confidence to us.
5,Good Packaging: 
Good Packaging:  Simulation Animatronic Customer Triceratops are covered with air bubble film before put them into the wooden case, which not only has good shock absorption, impact resistance, heat sealing and also has the advantages of nontoxic, odorless, moisture corrosion, good transparency etc.

 

Send your message to this supplier

*From:
*To:
avatar Mr. Sawyer Mak
*Message:

Enter between 20 to 4,000 characters.

This is not what you are looking for? Post a Sourcing Request Now